Javascript not enabled

 
Name: 
 

You must enter your name to take this test.

2001 District 7 Tractor Troubleshooting Test



True/False
Indicate whether the sentence or statement is true or false.
 

 1. 

Reciprocating motion is circular movement.
 

 2. 

The best pump for an open center system is the piston pump.
 

 3. 

A hydraulic pump creates pressure.
 

 4. 

Thermostats are not required when operating a modern engine in hot weather.
 

 5. 

The typical carburetor adjustments include load needle, idle speed,and idle mixture.
 

 6. 

When adjusting valve tappet clearance, set the respective cylinder a TDC of the exhaust stroke.
 

 7. 

The venturi in the carburetor slows the air flow.
 

 8. 

An interference valve seat is when the valve face and head are both the same angle.
 

 9. 

A high reading on the intake vacuum test on a diesel engine indicates an air intake restriction.
 

 10. 

A cylinder head can be checked for warpage by sighting across the flat surface.
 


Multiple Choice
Identify the letter of the choice that best completes the statement or answers the question.
 

 11. 

The free travel of the clutch pedal indicates:

a.

The clearance between the clutch release parts

b.

The clearance between the clutch plates

c.

The clearance between the pedal and the tractor frame

d.

The clearance between gear and pinion drives

 

 12. 

A compression ration of _________ is common for diesel engines.

a.

8 to 1

b.

12 to 1

c.

16 to 1

d.

40 to 1

 

 13. 

The camshaft turns at __________ the speed of the engine crankshaft.

a.

1/4

c.

2/3

b.

1/2

d.

None of these are correct

 

 14. 

Low battery charge may be due to:

a.

High speed engine operation

c.

Low engine temperature

b.

Continuous drain on battery

d.

Engine out of time

 

 15. 

Which is NOT a function of a radiator cap?

a.

Allows atmospheric pressure to enter the cooling system

b.

Prevents coolant escape at normal pressures

c.

Allow atmospheric pressure to escape the coolant

d.

All of these are correct

 

 16. 

The level of gasoline in the carburetor bowl is controlled by:

a.

Air bleeds

c.

Float

b.

Venturi

d.

Size of the inlet orifice

 

 17. 

To reduce the inside diameter of a valve guide use:

a.

A reamer

b.

A hone

c.

A knurler

d.

A boring bar

 

 18. 

What is the firing order of a six cylinder engine?

a.

153642

b.

152634

c.

153624

d.

135642

 

 19. 

If you loosen a high pressure fuel line to an injection nozzle and the engine misfires, that nozzle is probably:

a.

Good

c.

In need of cleaning

b.

Defective

d.

In need of replacement

 

 20. 

Two functions of plungers on inline injector pumps are __________ of fuel.

a.

Delivery and atomization

c.

Pressurization and delivery

b.

Injection and delivery

d.

Atomization and injection

 

 21. 

On most tractors, the main adjusting needle (power jet) of the carburetor controls the amount of:

a.

Fuel

b.

Air

c.

Vacuum

d.

None are correct

 

 22. 

A hydrometer is used to test:

a.

A battery

c.

Oil level

b.

Coolant level

d.

Distributor performance

 

 23. 

A tractor will deliver more horsepower at the:

a.

Belt pulley

c.

hydraulic cylinder

b.

Drawbar

d.

Attached implement

 

 24. 

Which type of oil pump is not commonly found in pressure lubrication systems on 4 cycle engines

a.

external gear pump

c.

plunger pump

b.

rotor pump

d.

vane pump

 



 

Check Your Work    Reset

Help